Changeset 857 for trunk/doc/expgui3.html

Timestamp:

Dec 4, 2009 5:13:14 PM (13 years ago)

Author:

toby

Message:

# on 2005/12/16 00:41:16, toby did:

pane --> panel

File:

• trunk/doc/expgui3.html (modified) (9 diffs, 3 props)

trunk/doc/expgui3.html

@@ -31 +31 @@
 <HR noshade width="75%" size="2" align="center">
 </h1></center>
-<h3>A.3 Histogram pane</h3> 
-<DL><DL>
-The histogram pane is used to edit background
+<h3>A.3 Histogram panel</h3> 
+<DL><DL>
+The histogram panel is used to edit background
 and diffractometer constants for a histogram, as well as 
 set damping and refinement flags for these parameters.
@@ -40 +40 @@
 <A href="expgui.html#multiplehistogram">
 "Multiple Histogram Selection" mode</A> is set to "All", 
-this pane is disabled. For other settings of this mode, 
+this panel is disabled. For other settings of this mode, 
 groups of histograms can be selected and modified 
 collectively.
@@ -47 +47 @@
 <A href="expgui.html#installation">(see the installation instructions)</A>
 is installed, a button for adding histograms will
-appear on the bottom right on this pane, as seen below. If the
+appear on the bottom right on this panel, as seen below. If the
 program is not properly installed, no errors occur, but the button
 does not appear.
 <P>
 Note that the order that histograms appear in this 
-pane is determined by the <a href="expguic.html#sorthist">"Sort histograms by"</a> option in 
+panel is determined by the <a href="expguic.html#sorthist">"Sort histograms by"</a> option in 
 the Options Menu.
 </DL></DL>
@@ -96 +96 @@
 The refinement flag and damping factor for correction for absorption
 effects (or for flat-plate samples, reflectivity corrections) can be 
-seen in a box near the bottom of the pane. 
+seen in a box near the bottom of the panel. 
 The terms and the type of correction used
 are set using the "Edit Abs./Refl." button in this box. Pressing this 
@@ -129 +129 @@
 <A href="expgui.html#multiplehistogram">
 "Multiple Histogram Selection" mode</A>).
-In this mode, the histogram pane
+In this mode, the histogram panel
 appears slightly differently, as is shown below.
 </DL></DL>
@@ -220 +220 @@
 described in an instrument parameter file. 
 Note that most of these instrumental parameters,
-such as wavelength or DIFC can be edited on this pane or 
-on the <A HREF="expgui5.html">profile</A> pane 
+such as wavelength or DIFC can be edited on this panel or 
+on the <A HREF="expgui5.html">profile</A> panel 
 (the simulated pattern is also affected by constants on the 
-<A HREF="expgui4.html">scaling</A> pane.)
+<A HREF="expgui4.html">scaling</A> panel.)
 The 2-theta/energy/TOF 
 range to be used for the computation, as well as the step size,
@@ -243 +243 @@
 <h3>A.3.5 Editing the Data Range & Excluded Regions</h3> 
 <DL><DL>
-The button at the bottom of the pane, labeled 
+The button at the bottom of the panel, labeled 
 "Set Data Limits & Excluded Regions" invokes
 the <a href="excledt.html">EXCLEDT</a> utility, which is used to 
@@ -253 +253 @@
 <DL><DL>
 <img SRC="3f.gif" align=RIGHT alt="EXPGUI Screen snapshot">
-The button at the bottom of the pane, labeled "Set Histogram Use Flags" invokes
+The button at the bottom of the panel, labeled "Set Histogram Use Flags" invokes
 a menu where the "Use"/"Do not use" flag for powder histogram can be set.
 When this flag is turned off, the histogram is ignored for
@@ -271 +271 @@
 <DL><DL>
 If there is more than one phase present in the refinement, 
-an extra box appears at the top of the pane to allow phase flags
+an extra box appears at the top of the panel to allow phase flags
 to be selected. This allows a phase to be used in some histograms
 but not in others. It also offers a simple way to effectively "delete" a